€395.00 + VAT

BGA-0245/0242
[70-0245/0242]

BGA-0245/0242

special converter, assigned for memories in BGA package, for example S29AL016MxxBxx01 in BGA48
top board: BGA-Top-2 ZIF-CS (order no. 70-0242)
bottom board: BGA-Bottom-1 (order no. 70-0245)
ZIF socket accepts many variations of BGA packages, that differ in ball diameter, ball width and package thickness.
The picture at Accepted package(s) section shows the range of all dimensions of BGA packages, which are accepted by this BGA-Top board.
operation life of ZIF socket - 500.000 actuations
order no.: 70-0245/0242

socket: ZIF BGA48 (accept package up to 48 balls), ClamShell type
bottom: 2 rows, 2x 24 pins, square, 0.6x0.6mm, rows spacing 600mil

Converter manual

Insert converter to the programmer ZIF socket according to the picture placed near of it. If you have some doubts about orientation of this converter in programmer ZIF socket, it is valid general rule, the orientation of the text of title is the same as the text on the top of the programmer.
Open the converter ClamShell ZIF socket. Insert the device into it (place device on contacts). The right position of the programmed device in converter ZIF socket is show on the picture in control program PG4UW (Device info for selected device).
Visually check position of device in converter ClamShell ZIF socket. If everything looks OK, close it and now, device is ready for programming.
Be careful, because the incorrect insertion of converter to the programmer ZIF socket or device to the converter ClamShell ZIF socket can damage the programmed device.
To take out the device, open converter ClamShell ZIF socket and remove device from it.
When you finish work with converter, remove it from the programmer ZIF socket.
Do not directly touch the pins of the converter and converter ZIF socket, because dirt may cause errors during programming of device.
For handling with the device we recommended to use a vacuum pick up tool.
The picture show, how to put together the BGA-Top-x ZIF-CS and BGA-Bottom-x boards to have complete BGA converter

Reviews

Shopping Cart

1 x	Four Jaw Chuck
1 x	Fixed Steady
1 x	Grinding mop cylinder grit 80
1 x	Precision steel vice PM 40
1 x	Multipurpose Vices Primus 75
1 x	Gear Chuck
1 x	Grinding mop cylinder grit 240
1 x	Tool holder for rotary tools
1 x	Grinding mop cylinder grit 120
1 x	Dividing attachment TA 230 for PF 250
1 x	Bench Circular Saw KS 230
1 x	Scroll saw DS 230/E
1 x	Sanding pads for OZI 220/E grit 150
1 x	Cut off/mitre saw KGS 80
1 x	2-speed scroll saw DSH
1 x	V-slot cutter 6.5mm
1 x	Three-jaw steel drill chuck
1 x	Edge cutter with pin 6.4mm
1 x	MICROMOT tool holder
1 x	MICRO cutter MIC
1 x	Core box bit 3.2mm
1 x	MICROMOT extension cord. 300cm.
1 x	Solid carbide saw blade
1 x	Table Saw FET
1 x	Slot cutter 3.2mm
1 x	Crosscut 'Super-Cut' blade
1 x	Angle cutter 45 °
1 x	Tungsten tipped saw blade
1 x	MICROMOT drill stand MB 200
1 x	PLCC Puller
1 x	HSS immersion saw blades for OZI
1 x	10-piece wood router cutter set
1 x	Grinding mop cylinder grit 120
1 x	Half round cutter 13mm
1 x	MICRO shaper MP 400
1 x	Diamond cutting blade for OZI
1 x	Aluminium Die-Cast
1 x	PLCC Extractor
1 x	Jig saw STS 12/E
1 x	Super-Cut
1 x	14-piece parallel supports set
1 x	Fluted filter for CW-matic
1 x	HSS cutting blade for OZI
1 x	Flexishaft MICROMOT 110/BF
1 x	Micro Compound Table KT 70
1 x	Tungsten Carbide Tipped (TCT)
1 x	Rebating cutter 6.4mm
1 x	Thicknesser DH 40
1 x	Saw blade made of high-alloy special steel
1 x	MICROMOT steel collet set
1 x	MICRO Band Saw MBS 240/E
1 x	HSS immersion saw blades for OZI
1 x	Slot cutter 5.0mm
1 x	MICRO woodturning lathe DB 250
1 x	Protective device for hand-operated MICROMOT
1 x	Rounding over cutter 6.4mm
1 x	Mill/Drill Unit BFB 2000.
1 x	Cutting disc, with reinforcement
1 x	Flexishaft MICROMOT 110/P
1 x	Sanding pads for OZI 220/E grit 240
1 x	Footswitch FS
1 x	Sanding pads for OZI 220/E grit 80
1 x	Super jig saw STS/E
1 x	Fine dust paper filter for CW-matic
1 x	Combi cutter 6.5/2.5mm
1 x	Surface planer AH 80
1 x	Diamond Coated
1 x	Diamond blade
1 x	IC tweezers
1 x	Slot cutter 6.5mm
1 x	Motor-driven carving device MSG
1 x	Coarse-toothed blades (No. 5: 36 teeth per 25mm)
1 x	Face clamping disc for D250X550
1 x	Polishing machine PM 100
1 x	Compact workshop vacuum cleaner CW-matic
1 x	BeeHive208S
1 x	Coarse-toothed blades (No. 3: 34 teeth per 25mm)
1 x	Pensander PS 13
1 x	Complete Engraving Kit with trial glass

€12,539.06