€395.00 + VAT

BGA-0245/0242
[70-0245/0242]

BGA-0245/0242

special converter, assigned for memories in BGA package, for example S29AL016MxxBxx01 in BGA48
top board: BGA-Top-2 ZIF-CS (order no. 70-0242)
bottom board: BGA-Bottom-1 (order no. 70-0245)
ZIF socket accepts many variations of BGA packages, that differ in ball diameter, ball width and package thickness.
The picture at Accepted package(s) section shows the range of all dimensions of BGA packages, which are accepted by this BGA-Top board.
operation life of ZIF socket - 500.000 actuations
order no.: 70-0245/0242

socket: ZIF BGA48 (accept package up to 48 balls), ClamShell type
bottom: 2 rows, 2x 24 pins, square, 0.6x0.6mm, rows spacing 600mil

Converter manual

Insert converter to the programmer ZIF socket according to the picture placed near of it. If you have some doubts about orientation of this converter in programmer ZIF socket, it is valid general rule, the orientation of the text of title is the same as the text on the top of the programmer.
Open the converter ClamShell ZIF socket. Insert the device into it (place device on contacts). The right position of the programmed device in converter ZIF socket is show on the picture in control program PG4UW (Device info for selected device).
Visually check position of device in converter ClamShell ZIF socket. If everything looks OK, close it and now, device is ready for programming.
Be careful, because the incorrect insertion of converter to the programmer ZIF socket or device to the converter ClamShell ZIF socket can damage the programmed device.
To take out the device, open converter ClamShell ZIF socket and remove device from it.
When you finish work with converter, remove it from the programmer ZIF socket.
Do not directly touch the pins of the converter and converter ZIF socket, because dirt may cause errors during programming of device.
For handling with the device we recommended to use a vacuum pick up tool.
The picture show, how to put together the BGA-Top-x ZIF-CS and BGA-Bottom-x boards to have complete BGA converter

Reviews

Categories

Manufacturers

Information

1 x	Slot cutter 5.0mm
2 x	Core box bit 3.2mm
2 x	V-slot cutter 6.5mm
1 x	Rounding over cutter 6.4mm
1 x	Lambswool polishing disc
2 x	Independent four jaw chuck for the DB 250
1 x	Half round cutter 13mm
1 x	Drill chuck with sliding sleeve for the tailstock
1 x	Super safety and specialty bit set, 75-piece
1 x	Super-fine sanding discs grain 2000
1 x	Polishing felt, medium hard
1 x	Slot cutter 3.2mm
1 x	Microfibre cloth
1 x	Super-fine sanding discs grain 400
1 x	Three jaw chuck for the lathe DB 250
1 x	Super-fine sanding discs grain 000
1 x	Edge cutter with pin 6.4mm
2 x	Angle cutter 45 °
1 x	Rebating cutter 6.4mm
1 x	Grinding mop cylinder grit 120
1 x	Five piece HSS chisel set
2 x	Universal and oil siphoning pump AP 12
2 x	Handy 1515
1 x	Combi cutter 6.5/2.5mm
1 x	Screwdriver bit set. 49-piece.
1 x	Cutter head for copy and surface milling MT2
1 x	BGA-Bottom-1
1 x	Stainless steel brushes
1 x	MICRO Heat gun MH 550
1 x	High quality corundum grinding bits
1 x	Stainless steel wheels
1 x	Brass brushes
1 x	Spare cutting wire
1 x	Cups brushes
1 x	Complete Engraving Kit with trial glass
1 x	BGA-Bottom-103
1 x	Engraving tool GG
1 x	6-piece screwdriver and cross-recess set
1 x	BeeProg2
1 x	BGA-Bottom-115
1 x	BGA-Bottom-10
1 x	6-piece screwdriver and cross-recess set
1 x	Hot wire cutter THERMOCUT 12/E
1 x	Replacement belts for BSL 220/E
1 x	Pinça SOIC de 8 pinos
1 x	Steel brushes
1 x	Hot wire cutter THERMOCUT 650
1 x	6-piece TORX-screwdriver-set
1 x	Universal holder UHZ
1 x	MICRO-screwdrivers

€2,915.54