Universal, ISP capable programmer
Short description:
- Info about the number of supported devices by
SMARTPROG2
- small, fast and powerful universal programmer
- DIL40 ZIF socket, devices in DIL package up to
40 pins are supported without adapters
- connector for in-circuit programming (ISP)
- connection to PC: USB port
- USB 2.0/1.1 compatible interface
- comfortable and easy to use control program,
Windows 95/98/Me/NT/2000/XP compatible
- free SW update, download from Internet
- power supply, cable and software included
- approved by CE laboratory to meet CE
requirements
- warranty - 3 years
Available accessories:
Note: see also SmartProg
programmer, that have identical features, but LPT port connection to PC.
Features
GENERAL
- SmartProg2 is the next member of new
generation of Windows 95/98/ME/NT/2000/XP based ELNEC universal
programmers. Programmer is built to meet the demands of development labs
and field engineers for universal, but portable programmer.
- SmartProg2 is a small, fast and
powerful programmer of all kinds of programmable devices. Using build-in
in-circuit serial programming (ISP) connector the programmer is able
to program ISP capable chips in-circuit. SmartProg2 isn't only a programmer,
but also a static RAMs tester.
- Provides very competitive price with
excellent hardware design for reliable programming. Nice "value for
money" in this class.
- Very fast programming due to high-speed
FPGA driven hardware and USB 2.0 full speed port.
- SmartProg2 interfaces with the IBM compatible
PC, portable or desktop personal computers through USB port, what is
important for new, LPT-port-less computers.
HARDWARE
- 40 powerful TTL pindrivers provide
H/L/pull_up/pull_down and read capability for each pin of socket. Advanced
pindrivers incorporate high-quality high-speed circuitry to deliver
signals without overshoot or ground bounce for all supported devices. Pin
drivers operate down to 1.8V so you'll be ready to program the full range of
today's advanced low-voltage devices.
- The programmer performs device insertion
test (wrong device position in socket) and contact check (poor
contact pin-to-socket) before it programs each device. These capabilities,
supported by signature-byte check help prevent chip damage due to
operator error.
- SmartProg2 programmer performs programming verification
at the marginal level of supply voltage, which, obviously, improves
programming yield, and guarantees long data retention.
- Various socket converters are available
to handle device in PLCC, SOIC and other packages.
SOFTWARE
- Programmer is driven by an easy-to-use
control program with pull-down menus, hot keys and on-line help. Selecting
of device is performed by its class, by manufacturer or simply by typing a
fragment of vendor name and/or part number.
- Standard device-related commands (read,
blank check, program, verify, erase) are enhanced by some test functions
(insertion test, signature-byte check), and some special functions
(autoincrement).
- All known data formats are supported.
Automatic file format detection and conversion during loading of file.
- The rich-featured autoincrement function
enables one to assign individual serial numbers to each programmed device -
or simply increments a serial number, or the function enables one to read
serial numbers or any programmed device identification signatures from a
file.
- The software also provide a many information
about programmed device. As a special, the drawing of all available
packages are provided. The software provide also explanation of chip
labelling (the meaning of prefixes and suffixes at the chips) for each
supported chip.
- The software provide a full information for
ISP implementation: Description of ISP connector pins for currently selected
chip, recommended target design around in-circuit programmed chip and other
necessary information.
CARE FOR THE CUSTOMERS
- It is important to remember that a support
most of the new devices requires only a software update due to the
SmartProg2 hardware. With our prompt service you can have a new device added
to the list of supported devices within hours! See AlgOR
(Algorithm On Request) service for details.
- Free software updates are available by download
from our WEB site.
- Keep-Current and AlgOR services, our next
step towards customer satisfaction.
- Keep-Current
service means, that ELNEC ships the latest version of
programmer software and updated user documentation (Keep-Current
package) to customer . The Keep-Current service is your hassle-free
guarantee that you are doing the highest quality programming on ELNEC
programmers, at minimal cost.
- AlgOR
(Algorithm On Request) service gives the user a tool to influence to
amount and types of programmed devices as needed.
- Advanced design of the SmartProg2 programmer
and careful manufacturing and burning allows us to provide a three-year
warranty on parts and labor for the programmer (limited 25 000-cycle
warranty on ZIF socket).
Specification
HARDWARE
Programmer
- two D/A converters for VCCP and VPP,
controllable rise and fall time
- VCCP range 2V..7V/350mA
- VPP range 2V..25V/200mA
- USB 2.0/1.1 compatible interface
- autocalibration
- selftest capability
ZIF socket, pindriver
- 40-pin DIL ZIF (Zero Insertion Force) socket
accepts both 300/600 mil devices up to 40-pins
- pindriver: 40 TTL pindrivers, specialized
GND/VCC/VPP pindriver
- FPGA based TTL driver provides H, L, CLK,
pull-up, pull-down on all pindriver pins; level H selectable from 1.8V up to
5V
- continuity test: each pin is tested before
every programming operation
ISP connector
- 10-pin male type with missinsertion lock
- 5 TTL pindrivers, provides H, L, CLK, pull-up,
pull-down; level H selectable from 1.8V up to 5V to handle all (low-voltage
including) devices.
- 1x VCCP voltage (range 2V..7V/100mA) (*1) and
1x VPP voltage (range 2V..25V/50mA)
- programmed chip voltage (VCCP) with both
source/sink capability and voltage sense
- (*1) - the programmer is not capable to
supply a target system from VCCP pin. If you have such demand, use please a
BeeProg programmer
DEVICE SUPPORT
Programmer, in ZIF socket
- EPROM: NMOS/CMOS, 27xxx and 27Cxxx series,
with 8/16 bit data width, full support of LV series (*1*2)
- EEPROM: NMOS/CMOS, 28xxx, 28Cxxx, 27EExxx
series, with 8/16 bit data width, full support of LV series (*1*2)
- Flash EPROM: 28Fxxx, 29Cxxx, 29Fxxx, 29BVxxx,
29LVxxx, 29Wxxx, 49Fxxx series, with 8/16 bit data width, full support of LV
series (*1*2)
- Serial E(E)PROM: 17Cxxx, 24Cxxx, 24Fxxx,
25Cxxx, 59Cxxx, 85xxx, 93Cxxx, full support of LV series(*1)
- Configuration PROM: 17xxx series, LV series
including
- NV RAM: Dallas DSxxx, SGS/Inmos MKxxx, SIMTEK
STKxxx, XICOR 2xxx, ZMD U63x series
- PLD: series: Atmel, AMD-Vantis, Cypress, ICT,
Lattice, NS, ... (*1)
- microcontrollers MCS51 series: 87Cxxx, 87LVxx,
89Cxxx, 89Sxxx, 89LVxxx series from Atmel, Atmel W&M, Intel,
Philips, SST, Winbond (*1*2)
- microcontrollers Atmel AVR: ATtiny, AT90Sxxx,
ATmega series (*1*2)
- microcontrollers Microchip PICmicro: PIC12xxx,
PIC16xxx, PIC17Cxxx, PIC18xxx series, 8-40 pins (*1*2)
- microcontrollers Scenix (Ubicom): SX18xxx,
SX20xxx, SX28xxx series
Programmer, through ISP
connector
- Microcontrollers Atmel: AT89Sxxx, AT90Sxxxx,
ATtiny, ATmega series
- Microcontrollers Microchip PICmicro: PIC12xxx,
PIC16xxx, PIC17xxx, PIC18xxx series
- Microcontrollers EM Microelectronic: 4 and 8
bit series
Notes:
- (*1) - suitable adapters are available for
non-DIL packages
- (*2) - there exist only a few adapters for
devices with more than 40 pins. Therefore, please, consider a more powerful
programmer (LabProg+, BeeProg, JetProg), if you need to program devices with
more than 40 pins
- for all supported devices see actual
DEVICE LIST
I.C. Tester
- Static RAM: 6116 .. 624000
Programming speed
| Device |
Operation |
Mode |
Time |
| 27C010 |
programming and verify |
in ZIF |
29 sec. |
| AT29C040A |
programming and verify |
in ZIF |
41 sec. |
| AM29F040 |
programming and verify |
in ZIF |
95 sec. |
| PIC16C67 |
programming and verify |
in ZIF |
10 sec. |
| PIC18F452 |
programming and verify |
in ZIF |
7 sec. |
| AT89C52 |
programming and verify |
in ZIF |
17 sec. |
| PIC16F876A |
programming and verify |
ISP |
5 sec. |
| PIC12C508 |
programming and verify |
ISP |
3 sec. |
Conditions: P4, 2.4 GHz, USB 2.0 high
speed, Windows XP.
The programming times are preliminary, the improvement is in progress.
SOFTWARE
Algorithms: only manufacturer approved or
certified algorithms are used. Custom algorithms are available at additional
cost.
Algorithm updates: software updates are
available approx. every 2 weeks, free of charge.
Main features: revision history, session logging, on-line help, device
and algorithm information.
Device operations
- standard:
- intelligent device selection by device
type, manufacturer or typed fragment of part name
- blank check, read, verify
- program
- erase
- configuration and security bit program
- illegal bit test
- checksum
- security
- insertion test
- contact check
- ID byte check
- special
- auto device serial number increment
- statistic
- count-down mode
Buffer operations
- view/edit, find/replace
- fill, copy, move, byte swap, word/dword split
- checksum (byte, word)
- print
File load/save
- no download time because programmer is PC
controlled
- automatic file type identification
Supported file formats
- unformatted (raw) binary
- HEX: Intel, Intel EXT, Motorola S-record,
MOS, Exormax, Tektronix, ASCII-SPACE-HEX
GENERAL
PC system requirements
Operation
- operating voltage 15..20V DC, max. 0.5A
- power consumption max. 6W active, about 1.4W
sleep
- dimensions 160x95x35 mm (6.3x3.7x1.4 inch)
- weight (without external power adapter) ca.
500g (17.65 oz)
- temperature 5°C ÷ 40°C (41°F ÷ 104°F)
- humidity 20%..80%, non condensing
Base configuration package includes
- SmartProg2 programmer
- wall plug adapter, 15V/500mA, unstabilized
- connection cable PC-programmer
- ISP cable
- diagnostic POD for selftest of the programmer
- anti-dust cover for ZIF socket
- user manual
- software
- registration card
- transport case
Additional services
- Keep
Current - ELNEC sends to user the latest version of
programmer software and updated user documentation (Keep-Current package)
- AlgOR
(Algorithms On Request) - add new supported devices on customer request
Programmer price also includes
- free technical support (hot line)
- free life-time software update via Internet
The information in this document is subject to change
without notice.
