Top » Catalog » Micromot tools » ACCESSORIES » Mains adaptor » 28704

€56.00 + VAT

MICROMOT Mains Adapter NG 5/E
[28704]

MICROMOT Mains Adapter NG 5/E

In compact NORYL casing (recommended for transformers). With superior capacity of 5.0 A at 16 Volt no load and 12 Volt under load = 60 VA (DC). Master switch for turning off transformer without needing to unplug. Red LED indicates "ready". PTC protection against overload (plugged-in machine will not restart automatically). Modern design with storage holes for tools with 2.35 mm and 3 mm shafts. Foldable tool rest provides a secure place for keeping the MICROMOT tool at the ready.

Technical Data:
Capacity: 5.0 A at 16 Volt no load and 12 Volt under load = 60 VA (DC). Primary supply 220/240 Volt. Thyristor electronic speed control (with feedback) for optimum tool speed and high torque at low speeds. 3 polarised sockets for MICROMOT machines. 1 pair of sockets for standard banana plugs (4 mm diameter).

Reviews

Customers who bought this product also purchased

MICRO Screwdriver MIS 1. Complete with 16 inserts.	MICROMOT extension cord. 300cm.	Spare cutting wire
Replacement cutting wire for the THERMOCUT 12/E	Hot wire cutter THERMOCUT 12/E	Hot wire cutter THERMOCUT 230/E

Categories

Manufacturers

Information

Shipping & Returns
Privacy Notice
Conditions of Use

Shopping Cart

1 x	Fine dust paper filter for CW-matic
1 x	Polishing felt, medium hard
1 x	Precision quick-action drill chuck 0-10mm B16
1 x	4-jaw chuck individually clamping 80mm
2 x	Footswitch FS
1 x	Precision quick-action drill chuck 0-16mm B16
1 x	centrically clamping 125mm
1 x	Precision magnetic gauge stand
1 x	3-jaw chuck centrically clamping 100mm
1 x	centrically clamping 100mm
1 x	Precision quick-action drill chuck 0-10mm B16
1 x	CM2 - B16 - M10
1 x	Morse taper MT3 - B16
2 x	MICROMOT Mains Adapter NG 2/S
1 x	4-jaw chuck individually clamping 100mm
1 x	Mill/Drill Unit BFB 2000.
1 x	Coarse-toothed blades (No. 3: 41 teeth per 25mm)
1 x	MICROMOT drill stand MB 200
1 x	MICROMOT extension cord. 300cm.
1 x	Independent four jaw chuck for the DB 250
1 x	Coarse-toothed blades (No. 3: 34 teeth per 25mm)
1 x	Diamond Coated
1 x	MICROMOT steel collet set
1 x	Tungsten Carbide Tipped (TCT)
1 x	14-piece parallel supports set
1 x	Micro Compound Table KT 70
1 x	Special Fused Alumina (Hardness N).
1 x	Coarse-toothed (25 TPI per 25mm)
1 x	Coarse-toothed (18 TPI per 25mm)
1 x	MICROMOT tool holder
1 x	Replacement glue sticks for HKP 220
1 x	Polishing Set
1 x	Flexishaft MICROMOT 110/BF
1 x	Silicon-Carbide.
1 x	Three jaw chuck for the lathe DB 250
1 x	Protective device for hand-operated MICROMOT
1 x	Coarse-toothed blades (No. 5: 17 teeth per 25mm)
1 x	Three-jaw steel drill chuck
1 x	Drill chuck with sliding sleeve for the tailstock
1 x	Aluminium Die-Cast
1 x	Flexishaft MICROMOT 110/P
1 x	Coarse-toothed (10 TPI per 25mm)
1 x	Coarse-toothed blades (No. 1: 50 teeth per 25mm)
1 x	Super-Cut
1 x	Coarse-toothed blades (No. 5: 36 teeth per 25mm)
1 x	Jig saw blades made of HSS
1 x	MICROMOT Mains Adapter NG 2/E
1 x	V-slot cutter 6.5mm
1 x	Supercut jig saw blades of special steel
1 x	Table Sawr TKS 315 E
1 x	Core box bit 3.2mm
1 x	Grinding mop cylinder grit 120
1 x	Slot cutter 6.5mm
1 x	Grinding mop cylinder grit 80
1 x	Edge cutter with pin 6.4mm
1 x	Step clamps made of steel
1 x	Machine Vice MS 4
1 x	10-piece wood router cutter set
1 x	Combi cutter 6.5/2.5mm
1 x	Grinding mop cylinder grit 120
1 x	Half round cutter 13mm
1 x	Angle cutter 45 °
1 x	Slot cutter 5.0mm
1 x	Wood Lathe DB900
1 x	Vacum SAA 901
1 x	Rounding over cutter 6.4mm
1 x	Precision steel vice PM 40
1 x	Tungsten carbide cutters set
1 x	Grinding mop cylinder grit 240
1 x	surface planing and thicknessing ADH 200
1 x	surface planing and thicknessing ADH 250
1 x	Wood Lathe DB450
1 x	Rebating cutter 6.4mm

€4,701.18